THE MOST POWERFUL IGNITION SYSTEM THE N55 COMMUNITY HAS EVER SEEN!

Our complete ignition system is designed to replace the factory pencil style coils which are prone to failure and incapable of properly supporting the needs of high horsepower applications. Our kits all comes complete with new ignition coils designed in house and manufactured to our specifications based on the needs and capability of the N55engine. 

Before now the only solutions for the N55 community were all pencil style coils which are incapable (due to size limitations) of producing the same output as larger Ignition Block style coils.  To make the best of the small package the pencil coil has, they are designed for high voltage output but very low current output.  This means the spark will bridge the gap on the spark plug and then disappear.  There is no duration to the spark and in the event the fuel does not ignite (or ignite fully) in that very short period of time you will have a misfire or incomplete burn.

Click to Enlarge

Because of the constraint of space to put components in a pencil coil reliable and proven ACDelco ignition coils(PN D585 / LS Truck Coils) paired with short plug wires are used in high horsepower applications everywhere. So why didn’t we just make a kit using these coils since they are the “standard” in many high horsepower applications? 

• Your car is specifically designed to run “Dumb Coils” and the ACDelco coils are “Smart Coils”

This leaves four options for adapting the car to work with them

1. Remove the factory DME and replace with Standalone system

      - Very costly & you lose some factory functions

2. Remove the factory DME and change circuitry of the board to control “Smart Coils” instead of “Dumb Coils”

- Not a plug and play solution you can do at home, requires sending off your factory DME for custom work

3. Add additional electronics to convert the IGBT output from the factory DME  back to 5V square wave to drive the “Smart Coils”

-  The factory system only has 1 IGBT system that can fail this solution has two IGBT systems that can fail, plus an additional converter box that can fail as well.  This results in 3 possible failure points.  In addition the DME no longer can “see” the coils which could cause other potential problems with how the computer is designed to monitor and react.

4. Use the IGBT negative output and constant power with resistor to drive the IGBT inside the "smart coil" backwards

-  As above the factory system only has 1 IGBT system that can fail this solution has two IGBT systems that can fail, plus a resistor which heats up and can fail as well. This results     in 3 possible failure points.  In addition the DME no longer can “see” the coils which could cause other potential problems with how the computer is designed to monitor and react.

-  Flashing of the DME to suppress errors caused by using "Smart Coils" in place of "Dumb Coils" is required

-  During testing of this approach it was found that the ignition coil produced about 1/2 of its original capability

-  Testing also showed an increased stress on the IGBT in the coils increasing the failure rate and overall longevity of the coil

• The ideal dwell time (calculated based on Duty cycle, RPM, and Duration) plays a big role in selecting the right ignition coil in any application

The maximum dwell time of 3.5ms is a fixed value for the N55 engine (allowing headroom for built motors turning more RPM)

1. The ACDelco coil has an ideal dwell time of close to 4.5ms

-  Since the ACDelco coil would only be allowed a maximum charge time of 3.5ms the output is greatly reduced to 90mj while the Precision Raceworks coil is capable of 118mj

So not only as explained above using a “SmartCoil” isn’t a great idea on the N55 as it is not designed for it you also need to consider the ideal dwell time allowed  by the car and the design of the coil when making the proper selection.  We have also included the quick reference chart below to better understand performance of the LS coil, OEM coil, PR coil,and for fun Lamborghini coil.  Showing that there is no standard each coil is designed to work within specific calculated dwell periods so the correct coil must be selected or designed for each application.

Why choose Precision Raceworks?

By designing our own coil we were able to take into account the available dwell time of the N55 as well as the IGBT system being built into the DME.  We were even able to take into consideration the ohm load of the factory BMW coil that came in the N55.  What this means is our coil looks exactly like the factory coil to the DMEmaintaining all functions allowing the computer to monitor and react as designed by the engineers at BMW.

Installation

Some trimming of the plastic covers and the plastic mount on the intake manifold may be required for fitment depending on the car.

Note for N55 Cars running PR coils: 

You need to take the O2 sensor wires and route them behind the cylinder head. They don’t need to be extended or anything just un-clip them from the bracket. If they are left in the stock location, they could end up close to the spark plug wires and the high voltage running through them would make the O2 sensors signal mess up.

N55 Precision Raceworks Ignition Coils Install - E90 335i

Compatibility Check

To ensure the part(s) you have ordered fits your vehicle, we run a compatibility check prior to dispatch. We can do this either using your registration number(UK) or the last 7 digits of your VIN. Simply enter your car details prior to checkout. 

Compatibility

BMW 1 Series

E82 & E88 135i (N55) 2011-2013

F20 & F21 M135i (N55) 2012+

BMW 2 Series

F22 & F23 M235i (N55) 2014+

F87 M2 (N55) 2014+ 

BMW 3 Series

E90/E91/E92/E93 335i (N55) 2011-2013

F30/F31 335i (N55) 2012+

BMW 4 Series

F32/F33/F36 435i (N55) 2014+

Free Next Day UK Delivery

Free Next Day UK Delivery if ordered before 11am on all in stock items! We can also ship worldwide, simply add the item(s) to cart and enter your full address at checkout for a shipping quote.

Manufactured by

Precision Raceworks

Part Number

601-0021 (Blue)

601-0108 (Black Edition)

Dimensions

61cm x 16cm x 12cm

Weight

3.8kg