The cookie settings on this website are set to 'allow all cookies' to give you the very best experience. Please click Accept Cookies to continue to use the site.

Carbon Fibre - Material, Installation, Aftercare & Warranty Info

 

READ ME BEFORE USING THIS PRODUCT

IMPORTANT INFORMATION REGARDING CARBON FIBRE PRODUCTS

 

Thank you for choosing SSDD MotorSport, a family-run business you can trust since 2003.

 

SSDD MotorSport specialises in supplying genuine and high quality aftermarket styling and performance products. Our products are developed to a high standard using the most modern technologies available such as wet laying, vacuum infusion, vacuum transfusion, and pre-preg with autoclave. Method of manufacturing selected for each product depending on the performance and market requirements of each product. All products are hand-made to the highest quality however minor flaws might still be present and we would like to take this opportunity to address these in detail.

 

MATERIALS

Carbon fibre is produced by thousands of threads sewed together in various patterns and directions. The patterns can be diagonal (2x2 3K twill weave), or straight (1x1 3K plain weave) for different visual and strength performances. Raw carbon fibre materials are supplied in huge rolls and often there are minor pattern imperfections. By imperfections we mean the threads are not aligned during the weaving process.

 

PRODUCT WITH MINIMAL FLAW

Whenever possible our manufacturing partners will try to avoid using these flawed sections of clothes however sometimes it is not possible to avoid them all together.

 

In most cases we lay the carbon fabric according to the best performance direction, and the reason for doing this is to provide the focus on overall rigidity rather than visual needs alone. However various shapes and edges on some products mean that the clothes need to be stretched to follow the curve resulting in a change in patterns. This visual imperfection is not considered a manufacturing defect but natural characteristics of hand-made products.

 

JOINT LINES

In some cases you might also notice some black glue or a black line in between edges of a product (e.g. spoiler). It is usually a result of the bonding of two combined products used to form the skeleton, as well as to reinforce the strength of a product. The black line is a joint line of a product made from two pieces combined together and an overlapped method is used to avoid wind trap.

 

INSTALLATION AND HANDLING

It is advisable that all composite products should be handled and installed by qualified technicians. Always wear protective clothes and use suitable tools. If in doubt please consult a qualified person or contact us for help.

 

Please be aware that aftermarket products requires experienced persons to fit, and in some cases modifications or removal of certain car body parts are required. The way some carbon fibre products are made means that the aftermarket product could become thicker or more ‘curved’ than the original part. These products will require trimming and removal of bumper or bonding agents for installation to achieve a better result. We try to supply fitting instruction whenever possible.

 

AFTERCARE

Carbon fibre by nature is a very strong product, however the resin and gelcoating and other chemicals used in the manufacturing process could react with heat and rays. We do not recommend using chemical based washing detergents to clean these products to avoid unwanted reactions.

 

After installation, check all fitment, bolts and screws and any bonding agents to be fully secure and set before set off in your vehicle. We advise checking the fixings on a regular basis as they could become loose.

 

MINOR DAMAGE REPAIR – Wet Sanding and Polishing

Although carbon fibre is very strong, however the surface gelcoat that give the product it’s shininess could be damaged when impacted.

 

If you happen to damage or scratch the surface of product, sometimes it is possible to carry out some DIY work to correct or improve these damages. Use good quality wet/dry sand paper in the follog order: 1000-1200-1500 Grits to remove minor scratches. We recommend using wet sanding method with soapy water. After sanding you may use cutting compound to remove the sanding marks, followed by quality polish/wax to bring the glossiness back to normal.

 

The wet sanding method can also be used to correct any minor scratches and swirl marks happened during delivery.

 

CAUTION: Take extra care when sanding, do not over sand as you could go through the surface gelcoat.

 

SHIPPING AND WARRANTY

We take every care in bringing you the best quality products and we pride ourselves on our industry leading customer services.

 

We examine all orders prior to shipping them to the customers, and we try to test everything we sell before offering them to the end users whenever possible.

 

We strongly advise you to check all contents when the package is delivered to make sure no damage has occurred during transportation and report any problems to us within 7 days. This will allow us to raise a claim with the shipping company as they have a time limit for reporting any shipping damages. Failing to inform us about this might result in your claims being declined.

 

In rare cases, if you find that a product has been damaged in transit or a fitment issue, please contact us by email info@ssdd-motorsport.com and we will try our best to resolve it for you in the quickest manner possible. When contacting us please include as many photos and as much details of the issue to help us deal with the enquiry more efficiently.

 

Our warranty on exterior products covers fitment issues only.

 

Unless otherwise stated, other branded products are covered by manufacturer’s own warranty and this could differ by brand.

 

WARRANTY EXCLUSIONS

We do not cover return shipping charges unless a product is faulty.

Damage caused to a product during installation or from use of parts not supplied by us.

Damage and changes in appearances caused by external forces and elements.

We reserve the rights to change the warranty conditions without prior notice.